-- *****************************************************************
-- OLD-CISCO-ENV-MIB.my: Cisco Environmental Monitor MIB file
--
-- May 1994, Jeffrey T. Johnson
--
-- Copyright (c) 1994 by cisco Systems, Inc.
-- All rights reserved.
--
-- *****************************************************************
--OLD-CISCO-ENV-MIB DEFINITIONS::=BEGINIMPORTSOBJECT-TYPEFROM RFC-1212
DisplayStringFROM RFC1213-MIB
local
FROM CISCO-SMI;lenv OBJECTIDENTIFIER::={ local 1}
-- lenv is the same as lsystem
-- we're just placing the envmon stuff under a new name for mibcompenvPresent OBJECT-TYPESYNTAXINTEGERACCESSread-onlySTATUSmandatoryDESCRIPTION"Is there an environmental monitor card in
this box?, 0 - No, 1-AGS card present, wrong
firmware, 2-AGS CARD present, firmware ok,
3-7000 support"::={ lenv 77}envTestPt1Descr OBJECT-TYPESYNTAXDisplayStringACCESSread-onlySTATUSmandatoryDESCRIPTION"Description of the test point 1. Typically
ambient air or the temperature of air
entering the router"::={ lenv 78}envTestPt1Measure OBJECT-TYPESYNTAXINTEGERACCESSread-onlySTATUSmandatoryDESCRIPTION"Current value of test point 1. Typically a
temperature in centigrade."::={ lenv 79}envTestPt2Descr OBJECT-TYPESYNTAXDisplayStringACCESSread-onlySTATUSmandatoryDESCRIPTION"Description of the test point 2. Typically
airflow or the temperature of air leaving the
router"::={ lenv 80}envTestPt2Measure OBJECT-TYPESYNTAXINTEGERACCESSread-onlySTATUSmandatory
DESCRIPTION"Current value of test point 2. Typically a
temperature in centigrade."::={ lenv 81}envTestPt3Descr OBJECT-TYPESYNTAXDisplayStringACCESSread-onlySTATUSmandatoryDESCRIPTION"Description of the test point 3. Typically
+5 volt"::={ lenv 82}envTestPt3Measure OBJECT-TYPESYNTAXINTEGERACCESSread-onlySTATUSmandatoryDESCRIPTION"Current value of test point 3. Typically the
value in millivolts of the +5v supply"::={ lenv 83}envTestPt4Descr OBJECT-TYPE
SYNTAXDisplayStringACCESSread-onlySTATUSmandatoryDESCRIPTION"Description of the test point 4. Typically
+12 volt"::={ lenv 84}envTestPt4Measure OBJECT-TYPESYNTAXINTEGERACCESSread-onlySTATUSmandatoryDESCRIPTION"Current value of test point 4. Typically the
value in millivolts of the +12v supply"::={ lenv 85}envTestPt5Descr OBJECT-TYPESYNTAXDisplayStringACCESSread-onlySTATUSmandatoryDESCRIPTION
"Description of the test point 5. Typically
-12 volt"::={ lenv 86}envTestPt5Measure OBJECT-TYPESYNTAXINTEGERACCESSread-onlySTATUSmandatoryDESCRIPTION"Current value of test point 5. Typically the
value in millivolts of the -12v supply"::={ lenv 87}envTestPt6Descr OBJECT-TYPESYNTAXDisplayStringACCESSread-onlySTATUSmandatoryDESCRIPTION"Description of the test point 6. Typically
-5 volt"::={ lenv 88}envTestPt6Measure OBJECT-TYPESYNTAXINTEGER
ACCESSread-onlySTATUSmandatoryDESCRIPTION"Current value of test point 6. Typically the
value in millivolts of the -5v supply"::={ lenv 89}envTestPt1MarginVal OBJECT-TYPESYNTAXINTEGERACCESSread-onlySTATUSmandatoryDESCRIPTION"Value at which the router will shutdown.
Typically the ambient air temperature that
will shut the router down. (e.g. 43)"::={ lenv 90}envTestPt2MarginVal OBJECT-TYPESYNTAXINTEGERACCESSread-onlySTATUSmandatoryDESCRIPTION
"Value at which the router will shutdown.
Typically the airflow air temperature that
will shut the router down. (e.g. 58)"::={ lenv 91}envTestPt3MarginPercent OBJECT-TYPESYNTAXINTEGERACCESSread-onlySTATUSmandatoryDESCRIPTION"+/- Percentage that will shut the router
down, (e.g. 10%) typically +5 volt"::={ lenv 92}envTestPt4MarginPercent OBJECT-TYPESYNTAXINTEGERACCESSread-onlySTATUSmandatoryDESCRIPTION"+/- Percentage that will shut the router
down, (e.g. 15%) typically +12 volt"::={ lenv 93}
envTestPt5MarginPercent OBJECT-TYPESYNTAXINTEGERACCESSread-onlySTATUSmandatoryDESCRIPTION"+/- Percentage that will shut the router
down, (e.g. 15%) typically -12 volt"::={ lenv 94}envTestPt6MarginPercent OBJECT-TYPESYNTAXINTEGERACCESSread-onlySTATUSmandatoryDESCRIPTION"+/- Percentage that will shut the router
down, (e.g. 10%) typically -5 volt"::={ lenv 95}envTestPt1last OBJECT-TYPESYNTAXINTEGERACCESSread-onlySTATUSmandatory
DESCRIPTION"Value of TestPt1 when last shutdown
occurred."::={ lenv 96}envTestPt2last OBJECT-TYPESYNTAXINTEGERACCESSread-onlySTATUSmandatoryDESCRIPTION"Value of TestPt2 when last shutdown
occurred."::={ lenv 97}envTestPt3last OBJECT-TYPESYNTAXINTEGERACCESSread-onlySTATUSmandatoryDESCRIPTION"Value of TestPt3 when last shutdown
occurred."::={ lenv 98}envTestPt4last OBJECT-TYPE
SYNTAXINTEGERACCESSread-onlySTATUSmandatoryDESCRIPTION"Value of TestPt4 when last shutdown
occurred."::={ lenv 99}envTestPt5last OBJECT-TYPESYNTAXINTEGERACCESSread-onlySTATUSmandatoryDESCRIPTION"Value of TestPt5 when last shutdown
occurred."::={ lenv 100}envTestPt6last OBJECT-TYPESYNTAXINTEGERACCESSread-onlySTATUSmandatoryDESCRIPTION"Value of TestPt6 when last shutdown
occurred."::={ lenv 101}envTestPt1warn OBJECT-TYPESYNTAXINTEGER{warning(1),noWarning(2)}ACCESSread-onlySTATUSmandatoryDESCRIPTION"Is this test point at a warning level?"::={ lenv 102}envTestPt2warn OBJECT-TYPESYNTAXINTEGER{warning(1),noWarning(2)}ACCESSread-onlySTATUSmandatory
DESCRIPTION"Is this test point at a warning level?"::={ lenv 103}envTestPt3warn OBJECT-TYPESYNTAXINTEGER{warning(1),noWarning(2)}ACCESSread-onlySTATUSmandatoryDESCRIPTION"Is this test point at a warning level?"::={ lenv 104}envTestPt4warn OBJECT-TYPESYNTAXINTEGER{warning(1),noWarning(2)
}ACCESSread-onlySTATUSmandatoryDESCRIPTION"Is this test point at a warning level?"::={ lenv 105}envTestPt5warn OBJECT-TYPESYNTAXINTEGER{warning(1),noWarning(2)}ACCESSread-onlySTATUSmandatoryDESCRIPTION"Is this test point at a warning level?"::={ lenv 106}envTestPt6warn OBJECT-TYPESYNTAXINTEGER{warning(1),
noWarning(2)}ACCESSread-onlySTATUSmandatoryDESCRIPTION"Is this test point at a warning level?"::={ lenv 107}envFirmVersion OBJECT-TYPESYNTAXDisplayStringACCESSread-onlySTATUSmandatoryDESCRIPTION"Description of Environmental Card firmware"::={ lenv 108}envTechnicianID OBJECT-TYPESYNTAXDisplayStringACCESSread-onlySTATUSmandatoryDESCRIPTION
"Technician ID"::={ lenv 109}envType OBJECT-TYPESYNTAXDisplayStringACCESSread-onlySTATUSmandatoryDESCRIPTION"The type of environmental card"::={ lenv 110}envBurnDate OBJECT-TYPESYNTAXDisplayStringACCESSread-onlySTATUSmandatoryDESCRIPTION"The calibration / burn in date"::={ lenv 111}envSerialNumber OBJECT-TYPESYNTAXDisplayStringACCESSread-onlySTATUSmandatory
DESCRIPTION"Serial Number of environmental monitor card"::={ lenv 112}END